Origin300, Quad-R14K/500 (2MB), 2GB RAM (1 bank), Fujitsu MAS 36GB 15K disk.

Tested on 21/Jan/2026.

Location: /hw/module/001c01/node
       IP45_4CPU Board: barcode MJP348     part 030-1728-002 rev -D
Location: /hw/module/001c01/Ibrick/xtalk/14
             IO8 Board: barcode MPV560     part 030-1673-004 rev -C
Location: /hw/module/001c01/Ibrick/xtalk/15
             IO8 Board: barcode MPV560     part 030-1673-004 rev -C
4 500 MHZ IP35 Processors
CPU: MIPS R14000 Processor Chip Revision: 1.4
FPU: MIPS R14010 Floating Point Chip Revision: 1.4
CPU 0 at Module 001c01/Slot 0/Slice A: 500 Mhz MIPS R14000 Processor Chip (enabled)
  Processor revision: 1.4. Scache: Size 2 MB Speed 250 Mhz  Tap 0x1a
CPU 1 at Module 001c01/Slot 0/Slice B: 500 Mhz MIPS R14000 Processor Chip (enabled)
  Processor revision: 1.4. Scache: Size 2 MB Speed 250 Mhz  Tap 0x1a
CPU 2 at Module 001c01/Slot 0/Slice C: 500 Mhz MIPS R14000 Processor Chip (enabled)
  Processor revision: 1.4. Scache: Size 2 MB Speed 250 Mhz  Tap 0x1a
CPU 3 at Module 001c01/Slot 0/Slice D: 500 Mhz MIPS R14000 Processor Chip (enabled)
  Processor revision: 1.4. Scache: Size 2 MB Speed 250 Mhz  Tap 0x1a
Main memory size: 2048 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Memory at Module 001c01/Slot 0: 2048 MB (enabled)
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
Integral SCSI controller 0: Version QL12160, low voltage differential
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL12160, low voltage differential
IOC3/IOC4 serial port: tty3
IOC3/IOC4 serial port: tty4
Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
  PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
IOC3/IOC4 external interrupts: 1
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c01/Slot n0: Revision 6.154
USB controller: type OHCI


STREAM TEST:

-------------------------------------------------------------
This system uses 8 bytes per DOUBLE PRECISION word.
-------------------------------------------------------------
Array size = 2000000, Offset = 0
Total memory required = 45.8 MB.
Each test is run 10 times, but only
the *best* time for each is used.
-------------------------------------------------------------
Number of Threads requested = 4
Number of Threads requested = 4
Number of Threads requested = 4
Number of Threads requested = 4
-------------------------------------------------------------
Your clock granularity/precision appears to be 5 microseconds.
Each test below will take on the order of 17079 microseconds.
   (= 3415 clock ticks)
Increase the size of the arrays if this shows that
you are not getting at least 20 clock ticks per test.
-------------------------------------------------------------
WARNING -- The above is only a rough guideline.
For best results, please be sure you know the
precision of your system timer.
-------------------------------------------------------------
Function      Rate (MB/s)   Avg time     Min time     Max time
Copy:        1353.4106       0.0215       0.0236       0.0245
Scale:       1301.6062       0.0222       0.0246       0.0253
Add:         1529.4422       0.0287       0.0314       0.0339
Triad:       1574.7463       0.0276       0.0305       0.0314
-------------------------------------------------------------
Solution Validates
-------------------------------------------------------------